Differences

This shows you the differences between two versions of the page.

--- stm32:peripherals:dma [2022/12/27 19:32] – [Programming Example] ruan
+++ stm32:peripherals:dma [2022/12/28 07:50] (current) – ruan
@@ Line 9: / Line 9: @@
   * 8 streams for each DMA controller, up to 8 channels per stream.
-  * 4 (32 bit wide) FIFO buffer per stream.
+  * 4 (32 bit wide) FIFO buffers per stream.
   * Programmable priority.
 \\
-===== Programming Example =====
-The code snippet bellow shows how to configure and use the DMA controller.
-<code c>
-#include "reg_stm32f4xx.h"
-RCC->AHBENR[0] |= (0x1 << 22u);      /* Enable DMA2 clock */
-/* Configure DMA2 controller. */
-DMA2->STREAM[0].CR |= (2u << 25u);   /* Setup channel. */
-DMA2->STREAM[0].CR |= (0x0 << 6u);   /* Setup direction. */
-DMA2->STREAM[0].CR |= (0x1 << 8u);   /* Setup circular mode. */
-DMA2->STREAM[0].NDTR |= 1u;          /* Setup nr of transfers. */
-/* Setup source and destination. */
-DMA2->STREAM[0].PAR |= (uint32_t) &(ADC3->DR);
-DMA2->STREAM[0].M0AR |= (uint32_t) &(TIM3->CCR[0]);
-/* Setup buffer size. */
-DMA2->STREAM[0].CR |= (0x1 << 11u);  /* PSIZE */
-DMA2->STREAM[0].CR |= (0x1 << 13u);  /* MSIZE */
-/* Start DMA transfer. */
-DMA2->STREAM[0].CR |= (0x1 << 0u);
-</code>
-\\
 ===== Configuration Registers =====
-==== SxCR ====
+==== DMA_SxCR - Stream X configuration register ====
-Stream X configuration register
 \\ {{dma_reg_sxcr.svg}} \\ \\
@@ Line 70: / Line 40: @@
 * Only writeable if EN = '0' \\ \\
-==== SxPAR ====
+==== DMA_SxPAR - Stream X peripheral address register ====
-Stream X peripheral address register
 \\ {{dma_reg_sxpar.svg}} \\ \\
@@ Line 79: / Line 47: @@
 |NDT|xxx|Number of data items to be transfered.|
-==== SxM0AR ====
+==== DMA_SxM0AR - Stream X memory 0 address register====
-Stream X memory 0 address register
 \\ {{dma_reg_sxm0ar.svg}} \\ \\
@@ Line 88: / Line 54: @@
 |M0A|xxx|Base address of memory 0.|
-==== SxM1AR ====
+==== DMA_SxM1AR - Stream X memory 1 address register ====
-Stream X memory 1 address register
 \\ {{dma_reg_sxm1ar.svg}} \\ \\
@@ Line 97: / Line 61: @@
 |M1A|xxx|Base address of memory 1.|
-==== SxNDTR ====
+==== DMA_SxNDTR - Stream X number of data register ====
-Stream X number of data register
 \\ {{dma_reg_sxndtr.svg}} \\ \\
@@ Line 105: / Line 67: @@
 |< 100% 5em >|
 |NDT|xxx|Number of data items to be transfered.|
+===== Programming Example =====
+The code snippet below shows how to configure and use the DMA controller.
+<code c>
+#include "reg_stm32f4xx.h"
+RCC->AHBENR[0] |= (0x1 << 22u);      /* Enable DMA2 clock */
+/* Configure DMA2 controller. */
+DMA2->STREAM[0].CR |= (2u << 25u);   /* Setup channel. */
+DMA2->STREAM[0].CR |= (0x0 << 6u);   /* Setup direction. */
+DMA2->STREAM[0].CR |= (0x1 << 8u);   /* Setup circular mode. */
+DMA2->STREAM[0].NDTR |= 1u;          /* Setup nr of transfers. */
+/* Setup source and destination. */
+DMA2->STREAM[0].PAR |= (uint32_t) &(ADC3->DR);
+DMA2->STREAM[0].M0AR |= (uint32_t) &(TIM3->CCR[0]);
+/* Setup buffer size. */
+DMA2->STREAM[0].CR |= (0x1 << 11u);  /* PSIZE */
+DMA2->STREAM[0].CR |= (0x1 << 13u);  /* MSIZE */
+/* Start DMA transfer. */
+DMA2->STREAM[0].CR |= (0x1 << 0u);
+</code>
+\\