Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
software:start:ct_board_test [2023/09/05 11:35] – [4) Test procedure] frttsoftware:start:ct_board_test [2023/09/08 07:38] (current) – frtt
Line 11: Line 11:
  
 ===== 4) Test procedure ===== ===== 4) Test procedure =====
-{{:getting_started:ct_board_test.jpg?600|}}+{{:getting_started:ct_board_test.jpg?1000|}}
  
-=== 4.1) DIP-Switch and LED === +=== 4.1) LCD Background Light === 
-<WRAP col2 box round 1000px left> +<WRAP box round 1000px left> 
-<WRAP 400px column> +The background light of the LCD should cycle through the colours: red, green and blue
-{{:getting_started:led_on.png?400px|}} +
-{{:getting_started:dip_switch_on.png?400|}} +
-Switch all dip-switches to the active position.\\ +
-All LED should be on, "moving" LEDs should be off.  +
-</WRAP> +
-<WRAP 400px column> +
-{{:getting_started:led_off.png?400|}} +
-{{:getting_started:dip_switch_off.png?400|}} +
-Switch all dip-switches to the inactive position.\\ +
-All LEDs should be off, "moving" LEDs should be on.  +
-</WRAP>+
 </WRAP> </WRAP>
 <WRAP clear></WRAP> <WRAP clear></WRAP>
  
-=== 4.2) 7 Segment Display ===+=== 4.2) Button & 7 Segment Display ===
 <WRAP col1 box round 1000px lef> <WRAP col1 box round 1000px lef>
 <WRAP 410px left> <WRAP 410px left>
Line 41: Line 30:
 <WRAP clear></WRAP> <WRAP clear></WRAP>
  
-=== 4.3) 7 GPIO Ports 1..4 === +=== 4.3) DIP-Switch & LED === 
-<WRAP col1 box round 1000px left> +<WRAP col2 box round 1000px left> 
-<WRAP 400px left> +<WRAP 400px column> 
-  - {{:ctboard:ctboard_mode_1.svg?50|}}\\ Please make sure the CT-Board is in the correct mode. Supported modes: 1  +{{:getting_started:led_on.png?400px|}} 
-  - {{:getting_started:lcd_status.png?400|}}\\ The status of the port is displayed on the LCD. +{{:getting_started:dip_switch_on.png?400|}} 
-  - {{:getting_started:push_button.png?400|}}\\ Insert the test plug in one of the port and push the corresponding button. +Switch all dip-switches to the active position.\\ 
-  - {{:getting_started:lcd_testresult.png?400|}}\\ The LCD should dipslay the testresul either with an X or with a ✓. +All LED should be on, "moving" LEDs should be off. 
 </WRAP> </WRAP>
-</WRAP> 
-<WRAP clear></WRAP> 
- 
-=== 4.4) GPIO Ports P5/P6 === 
-<WRAP col1 box round 1000px left> 
 <WRAP 400px column> <WRAP 400px column>
-  - {{:getting_started:lcd_status.png?400|}}\\ The status of the port is displayed on the LCD.\\ +{{:getting_started:led_off.png?400|}} 
-  - Insert a flat ribbon cable from P5 to P6.\\ +{{:getting_started:dip_switch_off.png?400|}} 
-  - {{:getting_started:lcd_testresult.png?400|}}\\ The LCD should display the testresult for P56 either with an X or with a ✓. +Switch all dip-switches to the inactive position.\\ 
 +All LEDs should be off, "moving" LEDs should be on. 
 </WRAP> </WRAP>
 </WRAP> </WRAP>
 <WRAP clear></WRAP> <WRAP clear></WRAP>
  
-=== 4.5) Potentiometer ===+=== 4.4) Potentiometer ===
 <WRAP col2 box round 1000px left> <WRAP col2 box round 1000px left>
 <WRAP 400px column> <WRAP 400px column>
Line 79: Line 64:
 <WRAP clear></WRAP> <WRAP clear></WRAP>
  
-=== 4.6) HEXSW ===+=== 4.5) HEX-Switch ===
 <WRAP column box round 1000px left> <WRAP column box round 1000px left>
 <WRAP 400px left> <WRAP 400px left>
 +{{:getting_started:lcd_hexsw_value.png?400|}}
 {{:getting_started:hex_switch_turn.png?100|}} {{:getting_started:hex_switch_turn.png?100|}}
   - Turn the HEX-Switch one step.   - Turn the HEX-Switch one step.
   - On the LCD the value should be displayed.   - On the LCD the value should be displayed.
-{{:getting_started:lcd_hexsw_value.png?400|}} +  - Repeat 1. and 2. until all possibilities are checked (0..9, a..f).
-Repeat 1. and 2. until all possibilities are checked (0..9, a..f).+
 </WRAP> </WRAP>
 </WRAP> </WRAP>
 <WRAP clear></WRAP> <WRAP clear></WRAP>
  
-=== 4.7) LCD Background Light === +=== 4.6) GPIO Ports P5/P6 === 
-<WRAP box round 1000px left> +<WRAP col1 box round 1000px left> 
-The background light of the LCD should cycle through the colors: red, green and blue+<color #ed1c24>REQUIRES ADDITIONAL HARDWARE!</color> This test requires flat ribbon cable,\\ 
 +which you will find in the laboratory. Skip this test if you do not have access to it. 
 +<WRAP 400px column> 
 +  - {{:getting_started:lcd_status.png?400|}}\\ The status of the port is displayed on the LCD.\\ 
 +  - Insert a flat ribbon cable from P5 to P6.\\ 
 +  - {{:getting_started:lcd_testresult.png?400|}}\\ The LCD should display the testresult for P56 either with an X or with a ✓. 
 </WRAP> </WRAP>
 +</WRAP>
 +<WRAP clear></WRAP>
 +
 +=== 4.7) 7 GPIO Ports 1..4 ===
 +<WRAP col1 box round 1000px left>
 +<color #ed1c24>OPTIONAL:</color> This test requires additional hardware.\\ 
 +Skip this test if you do not have access to it.
 +<WRAP 400px left>
 +  - {{:ctboard:ctboard_mode_1.svg?50|}}\\ Please make sure the CT-Board is in the correct mode. Supported modes: 1 
 +  - {{:getting_started:lcd_status.png?400|}}\\ The status of the port is displayed on the LCD.
 +  - {{:getting_started:push_button.png?400|}}\\ Insert the test plug in one of the port and push the corresponding button.
 +  - {{:getting_started:lcd_testresult.png?400|}}\\ The LCD should dipslay the testresul either with an X or with a ✓. 
 +</WRAP>
 +</WRAP>
 +<WRAP clear></WRAP>
 +
 +
  
  • software/start/ct_board_test.1693913731.txt.gz
  • Last modified: 2023/09/05 11:35
  • by frtt